We had the E-TEC 300-hp mounted to the stern of a Dusky 233, and while this isn’t a boat report, the combination was impressive. Test weight was just over 4600 lbs. (2086 kgs.), and top speed came in at 5650 rpm and a respectable 51.7 MPH. That gave us a fuel burn of 26.2 gph and 1.97mpg. Dialed back to a more reserved pace, 3500 rpm showed a best cruise of 28.8 MPH, a fuel burn of 9.3 gph, and 3.11 mpg. Time to plane was 4.6 seconds, and we reached 30 MPH in 7.7 seconds.
Comparison to Other Engines
In looking over our tests of other center console boats in class powered by other engine brands, we didn’t find any powered by a single 300-hp. Next, we checked the performance testing of the outboard companies looking for a 300-hp single engine CC in boats with a dry weight of about 3700 lbs., which is what our Dusky weighed. Bingo! One of the makers of a 4-stroke 300-hp engine had done their own test on a sistership of the same Dusky 233 we tested.
A Comparison Caveat
This is potentially one of the most apples-to-apples comparisons we have seen, but we hasten to add that these kinds of tests, even when done with BoatTEST.com's captains at different places, at different times on the same model are never apples-to-apples. There are always differences in temperatures, weight of the two people aboard, liquid levels, wind and water conditions, humidity, prop geometry or material, testing gear and tester technique. Further, no two sisterships are exactly the same weight, and even if was exactly the same boat, we tested the Dusky 18 months after the 4-stroke engine maker so the boats was likely heavier.In this case the recorded date shows that is was 14-degrees F hotter when we tested the Evinrude and the boat was probably 350 lbs. 159 kgs.) heavier because we had a full load of fuel aboard not a half load as in the 4-stroke test. With that caveat, the performance numbers are breath-takingly similar. To us, this was an important affirmation of Evinrude's claim to be as fuel-efficient as 4-stroke engines. If you remember the old 2-stroke engines of yesteryear and how they guzzled gas, then you will be amazed at what the new Evinrude's E-TEC engines consume.
Evinrude 2-Stroke vs. Brand-X 4-Stroke
In this comparison of data at 5500 rpm we clocked the Evinrude 300 at 50.3 mph, 1.0 mph faster than the 4-stroke adversary which reportedly went 49.25 mph. We measured a miles per gallon for the Evinrude at 1.92, and the 4-stroke did slightly better at 2.03 -- 0.11 mpg more! At WOT, it was a slightly different story, with the Evinrude 300 again being faster at 51.7 mph (at 5650 rpm) and the 4-stroke 300 clocked at 51.6 (at 5800 rpm). Not surprisingly, The Evinrude got better fuel mileage at WOT than the 4-stroke, getting 1.97 mpg compared with 1.93 mpg -- 0.04 mpg better! At the all-important "Best Cruise" we clocked the Dusky 233 powered by the Evinrude 300 at 3500 rpm going 28.8 mph, getting 3.11 mpg. The 4-stroke 300-hp engines reportedly went 24.45 mph at 3500 (which was also its "Best Cruise") and got 3.15 mpg -- 4.35 mph slower getting 0.04 mpg more. As we said, these numbers are breath-takingly similar.
The E-TEC 300 Features
The skeg is large enough, starting at 5 3/4” and increasing to 12” as it rises above the prop. The lower unit itself is a an SLE (Straight Leading Edge) and it has it’s water intakes on the forward section of the lower unit, forward of the prop. A second water intake is mounted to either side of the casing and each measures 1 ½” and they’re removable for easy cleaning. Also mounted to the forward end of the lower unit was pickup for the speedometer. This means no drilling into your boat for mounting a pitot. Great feature. The propeller on our test boat was a 15 1/4x19”P Rebel. The anti-ventilation plate measures 21 1/2”x6” and included a trim tab hanging underneath to counter torque. I love the engine mounted trim switch, and even though that’s not a new or even unique feature, this one has a limiting switch that prevents the cowling from coming into contact with a splash-well or high transom. Plus, it’s adjustable by the end user with no tools. And while the engine is tilted up, you can lower the attached trailer bracket to take the load off the hydraulics while trailering. The main electrical harness is conveniently located, as you can see in the video, and for once, someone got the brilliant idea to mount a spare fuse right at the harness connection. Thank you, Evinrude.
Not only is there a thru-hub exhaust, but there are dual ports above the waterline as well. The upper is for engine exhaust, and the lower for cooling water. That lower cooling water port is also fitted with a tell-tale stream that you can direct as you desire with nothing more than a spark plug wrench. Removing the fitting entirely allows you to attach a garden hose for flushing the engine out with fresh water.
Stopping Engine Knock
Getting a dose of bad gas can start an engine knock that could cause serious damage. Evinrude E-TEC 300 H.P. comes with a “knock” sensor that detects a bad burn and corrects it, saving the engine from damage, the company says. We’ve all had senders that have had to be replaced now and then. I couldn’t help but notice that on the 300, the thermostats were easily accessible, and believe it or not, they’re replaceable with just a spark plug wrench. Speaking of self-servicing items, the fuel filter deserves a mention. First it’s mounted with the screw attachment facing up. Some have these facing down for some reason, and when you unscrew them, they dump fuel all over the place. These keep everything nice and tidy. The fuel filter is also a water separator, and if water does get into the system, a signal alerts you to the need for a filter change, and likely a fuel change as well.
The E-TEC 300 H.P. is an easy-to-operate engine. It uses a system Evinrude calls I-CON™. A digital throttle control sends a signal to an electronic servo that is in turn connected to the shift and throttle linkages. The result is a gentle control for both shift and speed. This is a great feature as you won’t experience cable stretch or linkage problems affecting your control travel. The downside is if you’re one of those people like me who tend to rest your hand on the control at all times, then each bounce of the boat will result in a speed change. Small price to pay and I just moved my hand from the top of the engine control to the base, then wrapped my fingers around the shaft of the engine control and problem solved. The digital world that this engine lives in also comes into play with the I-Command™ gauges. They’re multi function and totally customizable. We had three separate ones that were showing dual bits of info that we set them up for. One had engine temp and voltage, another showed RPM and GPH, and another showed MPH and MPG. I like that these are customizable as different operators like to have different choices on what they like to have displayed at a glance.
...Or at least “see ya later”. While nothing can eliminate corrosion in metal parts when combined with warm salt water, Evinrude has gotten on the stick to slow it to a crawl so that it takes a longer time to show itself, according to company engineers. (We have yet to test this aspect of the Evinrude engines, but we plan to.) The company's engineers tell us that their anti-corrosion approach is a four- part process.
- A Lyfinite treatment – this is a trademarked process and Evinrude owns the trademark. It puts the first protective coating on the metal components.
- EDP – Electro Deposition Paint – this is based on the fundamental physics principle that opposites attract. The metal parts are charged with direct current and then immersed in a bath that has oppositely charged paint particles in it. This allows every corner, crack, and crevice to have a continuous even coating over the entire surface of the part.
- Primer is then added.
- Finally the finish coat.
When buying an outboard motor there are seven things that seem to us that everyone should want –
- Fuel Efficiency
- Enough power for the job
- Low maintenance costs
- Good Warranty
Test Result Highlights
- Top speed for the Dusky 233 Open (2010-) is 51.7 mph (83.2 kph), burning 26.2 gallons per hour (gph) or 99.17 liters per hour (lph).
- Best cruise for the Dusky 233 Open (2010-) is 28.8 mph (46.3 kph), and the boat gets 3.11 miles per gallon (mpg) or 1.32 kilometers per liter (kpl), giving the boat a cruising range of 280 miles (450.62 kilometers).
- Tested power is 1 x 300-hp Evinrude E-TEC 300 H.P..
Standard and Optional Features
|Dripless Shaft Seals||Optional|
|Washdown: Fresh Water||Optional|
|Washdown: Raw Water||Optional|
Boats More Than 30 Feet
(It's quick and FREE!)